docker version of ogn2readsb

consisting of the following components:

• ogn2dump1090
  • simple Python tool to inject Open Glider Network Traffic (from an existing local OGN decoder instance) into an existing readsb ADS-B decoder instance for display on a unified tar1090 map
  • furthermore online aggregated traffic from aprs.glidernet.org can optionally be injected for a reasonably selected radius around a given location
  • OGN traffic will be displayed as other traffic alongside with ADS-B traffic, using the readsb tar1090 webinterface (e.g. http://yourRaspberryPi.local/tar1090/)
• rtlsdr-ogn (feeding glidernet.org with OGN traffic)
• readsb (feeding glidernet.org with ADS-B traffic and decoding/forwarding traffic to the tar1090 map)
• mlat-client-adsbx (display MLAT traffic from adsbexchange.com)
• tar1090 (traffic map)
• optional feeds:
  • adsbexchange.com
  • airplanes.live
  • adsb.lol
  • adsb.fi
  • planefinder.net
  • flightradar24.com
  • airnavradar.com
  • flightaware.com
  • opensky-network.org

supported operating systems

Debian or Debian-based Linux Operating Systems (64bit Debian 13 Trixie or newer):

• Debian
• Ubuntu
• DietPi
• RaspiOS

supported hardware architectures

• arm64 (64-bit ARM CPUs with hardware floating point processor)
• x64 (64-bit AMD/Intel CPUs)
• SDRs: native support of RTL-SDR Blog v4 SDR since Debian 13 Trixie

prepare system

• sudo apt update && sudo apt install git
• you may be asked Y/n a couple of times, it is safe to answer all of them with Y

prepare docker

• wget -q https://raw.githubusercontent.com/sdr-enthusiasts/docker-install/main/docker-install.sh && chmod +x docker-install.sh
• nano docker-install.sh and remove/disable lines #33 and #41 (software-properties-common, netcat)
• ./docker-install.sh
• you may be asked Y/n a couple of times, it is safe to answer all of them with Y
• sudo reboot

prepare SDRs

• identify or set both SDR serials (e.g. 868 and 1090), they are required for the config.vars below
• unplug all SDRs, leaving only the SDR to be used for 1090 MHz reception plugged in, then issue the following command:
  • docker run --rm -it --device /dev/bus/usb --entrypoint rtl_eeprom ghcr.io/sdr-enthusiasts/docker-adsb-ultrafeeder -s 1090
• unplug all SDRs, leaving only the SDR to be used for 868 MHz reception plugged in, then issue the following command:
  • docker run --rm -it --device /dev/bus/usb --entrypoint rtl_eeprom ghcr.io/sdr-enthusiasts/docker-adsb-ultrafeeder -s 868

prepare ogn2readsb

• git clone https://github.com/VirusPilot/docker-ogn2readsb

configuration

• cd ./docker-ogn2readsb
• nano config.vars
  • save changes with CTRL O
  • exit nano with CTRL X

variable	example	description
STATION_LAT	50.0	your station latitude [deg] (as positive or negative decimal number)
STATION_LON	10.0	your station longitude [deg] (as positive or negative decimal number)
STATION_ALT_MSL_M	300	your station altitude AMSL [m]
STATION_NAME	OGNTEST	your max. 9 letter station name, please comply with naming convention
STATION_INFO	Raspberry Pi5	optional information (up to 63 characters) about your station, e.g. contact information or hardware details
FREQ_PLAN	1	1=EU/Africa (default), 2=USA/Canada, 3=South America/Australia, 4=New Zeeland, 5=Israel, 6=EU/Africa 433MHz
GSM_CENTER_FREQ	935.8	default = 0, change only if you know your closest GSM900 station frequency [MHz]
ADSB_MAX_ALT_FT	18000	ADSB max OGN feed altitude [ft]
METAR_SOURCE_ICAO	EDDF	4 letter ICAO code of a nearby airport with METAR service
APRS_SUBSCRIBE_FILTER	r/50.0/10.0/100	circle in [km] around a defined postion (example: LAT 50.0, LON 10.0, CIRCLE 100 km) for which you want to receive traffic from the OGN APRS servers
SDR_868_SERIAL	868	enter your OGN SDR serial
SDR_868_PPM	0	change only if you know your SDR's ppm
SDR_868_BIAS_T_ENABLE	0	set to 1 to enable Bias Tee on your SDR, e.g. to power a LNA
SDR_1090_SERIAL	1090	enter your ADSB SDR serial
SDR_1090_PPM	0	change only if you know your SDR's ppm
SDR_1090_BIAS_T_ENABLE	0	set to 1 to enable Bias Tee on your SDR, e.g. to power a LNA

option to merge inconsistent address type transmissions

• cd ./docker-ogn2readsb
• nano tar1090/Dockerfile
• add && echo 'MergeNonIcao = true;' >> config.js after echo 'jaeroLabel = "OGN";' >> config.js

build (only feeding glidernet)

• cd ./docker-ogn2readsb
• docker compose up --detach --build
• you may be asked Y/n a couple of times, it is safe to answer all of them with Y
• sudo reboot

ADVANCED build (with addidtional feeders)

• cd ./docker-ogn2readsb
• nano compose-multifeed.yaml
  • add your feeder credentials (e.g. SHARING KEY, USERNAME, LAT, LON, ALT)
  • delete (or comment out) unused/unwanted feeder entries
• docker compose --file compose-multifeed.yaml up --detach --build
• you may be asked Y/n a couple of times, it is safe to answer all of them with Y
• sudo reboot

apply configuration changes

• cd ./docker-ogn2readsb
• nano config.vars
• docker compose up --detach --build or docker compose --file compose-multifeed.yaml up --detach --build
• docker compose up --detach --build --force-recreate or docker compose --file compose-multifeed.yaml up --detach --build --force-recreate

monitor all ADSB and OGN traffic consolidated in a single tar1090 instance

• http://yourReceiverIP.local/tar1090

enable DE and AT traffic patterns

• quick hack for now: enable "UK Radar Corridors":

monitor OGN details

• http://yourReceiverIP:8080
• http://yourReceiverIP:8081

monitor docker containers

• docker logs -f rtlsdr-ogn
• docker logs -f mlat-client-adsbx
• docker logs -f readsb
• docker logs -f ogn2dump1090
• docker logs -f tar1090

useful docker commands

• docker ps -a list all docker containers, including stopped ones
• stop and deactivate containers
  • docker stop <container_name_or_id> stop a running container
  • docker rm <container_name_or_id> deactivate a stopped container
  • docker container prune remove all stopped containers
  • docker compose down stop and remove containers, networks
  • docker compose up --detach create and start containers
  • docker compose up --detach --build build, create and start containers
• list and delete unused docker images
  • docker image ls list docker images
  • docker rmi <image_id_or_name> delete unused docker image
  • docker image prune delete all unused docker images
• remove unused data e.g. to save space
  • docker system prune
• clean your entire docker environment e.g. for a fresh docker compose
  • docker rm -f $(docker ps -aq) force remove ALL containers
  • docker system prune -af --volumes clean your docker environment
• open a shell inside your container
  • docker exec -it <yourDockerContainer> bash