Replies: 31 comments 7 replies
-
|
|
Beta Was this translation helpful? Give feedback.
-
|
if its a car without a reverse camera and you have put it on as an add on/upgrade I should imagine you will have to enable rear reverse camera in the navigation section with DDT4ALL on your rlink2 |
Beta Was this translation helpful? Give feedback.
-
|
Yes its is new and activated with ddt4all. it has now the camera menu, but says defet camera or missing signal. so i think i dident use the right pins? i have bought at adapter but it is 32 pin and the radio has 24 pin so i found the connections on the picture but i dont work |
Beta Was this translation helpful? Give feedback.
-
|
is your camera a 12v or 6v power requirement? |
Beta Was this translation helpful? Give feedback.
-
|
it is 6 volt. if i connect camera wit power from extern cable there is still no video signal on r link . but there is picture if i connect the video cable to a old tv... |
Beta Was this translation helpful? Give feedback.
-
|
strange , should work then you would think. - so you are using the +6v and -6v pins and the CVBs + and - and putting car into reverse gear and no pic ? - where did you get the 24pin wiring detail diagram from. here is wiring for rlink1 but I dont know if it the same for rlink2:
|
Beta Was this translation helpful? Give feedback.
-
|
I think I saw it on this site and it fit fine with the pins that were not in use. so just like you have shown here but - for the camera supply I have taken out the rear lights. But it is not only the power that has problems, because I have tried to supply the camera with external power, so the video signal is also wrong. When the car is put into reverse gear, a black screen appears and it reports a camera error or lack of signal |
Beta Was this translation helpful? Give feedback.
-
|
yes, it could possibly be different wiring for the rlink2 vs the rlink1 24 pin connector then |
Beta Was this translation helpful? Give feedback.
-
|
My thought is that mabye there i a different wirring in r-link2 ? |
Beta Was this translation helpful? Give feedback.
-
|
I found this - pin 21 could it be on the 32pin cable?
|
Beta Was this translation helpful? Give feedback.
-
|
the emty wire holes in my radio is 1,3,4,5,12,14,16,18,19,20,21 . when i have been surfing on the web i have seen a lot of r-link 2 with 32 pin connector, the problem is that mine is a 24 pin and cant find any diagram with 24 pin for r-link 2 so i could be sure of which wires i shoul use |
Beta Was this translation helpful? Give feedback.
-
|
Thank you Andy, I hope someone have the wire connection for r-link 2 so i for sure can find the faul |
Beta Was this translation helpful? Give feedback.
-
|
havent found a wiring diagram - but this sounds like the kind of lead you need maybe if yours is a 24pin plug:
|
Beta Was this translation helpful? Give feedback.
-
|
Yes it would be great, but im not sure if the wirring is correct. Its for the elder medinav, i have seen som sellers write , that it wont support r-link? |
Beta Was this translation helpful? Give feedback.
-
|
You need a diagram for the connection ? I can give you… I need your VIN the lead at the picture is for MediaNav UlC4 not for RLink. It’s different. |
Beta Was this translation helpful? Give feedback.
-
|
Vin nr. vf1rfa00063460938 thankyou |
Beta Was this translation helpful? Give feedback.
-
vf1rfa00063460938 thank you :-) |
Beta Was this translation helpful? Give feedback.
-
|
|
Beta Was this translation helpful? Give feedback.
-
|
Apropos… you have to visit a garage, there is a OTS to reprogramming your ECUs |
Beta Was this translation helpful? Give feedback.
-
|
My German is not the Best ;-) is it corrett i should use pin 2,3,5. The car already have a wire in pin 2? |
Beta Was this translation helpful? Give feedback.
-
|
Im not shure if you have the correct connection. Normally you use the connection from „Radio“ behind the Clovebox. There I can’t find so long the diagram. But I have attached you the manual to install the camera system originally. There are the correct instructions an a diagram to connect. I hope it’s helpful. |
Beta Was this translation helpful? Give feedback.
-
|
Thank you so much :-) my fault i have trying to connect on the back of r-link screen an not behandling the clovebox. So i learned a lesseon today |
Beta Was this translation helpful? Give feedback.
-
|
so did you have to join your camera wires to the 32pin connector then? |
Beta Was this translation helpful? Give feedback.
-
|
Hi? I need some schemes of the rlink2 (unit + screen) and the UCH. Can you help with it? |
Beta Was this translation helpful? Give feedback.
-
|
|
Beta Was this translation helpful? Give feedback.
-
|
i have the same issue brother , have you managed to find a solution brother ? |
Beta Was this translation helpful? Give feedback.
-
|
Ineed pin location for clio5 |
Beta Was this translation helpful? Give feedback.
-
|
Is not ok this tutorial #1246 ? |
Beta Was this translation helpful? Give feedback.
-
|
@matzel82 could you please help with the PIN/wiring diagram of the UCH for this VIN please? VF1RFB00163819901 Thank you. |
Beta Was this translation helpful? Give feedback.
-
|
Hello, could anybody help with renault espace 5 (2016 year) Telematic control unit connector pin diagram? |
Beta Was this translation helpful? Give feedback.
-
|
Why you need that for 😅
Op vr 1 aug 2025, 17:10 schreef AndriyNakonechnyy ***@***.***
…:
Hello, could anybody help with renault espace 5 (2016 year) Telematic
control unit connector pin diagram?
—
Reply to this email directly, view it on GitHub
<#1040 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/BNOTOHS42FNG43W5EQVW6Y33LN7MVAVCNFSM6AAAAAB2WOT2EOVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGOJWGAYTINI>
.
You are receiving this because you are subscribed to this thread.Message
ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
This module is locked in my car and i don |
Beta Was this translation helpful? Give feedback.
-
|
It hard to replace the tcu untit.. its register on renault servers ect
ect.. better buy new one or go to dealer.. if you want to chech wich
service are active an wich not you can contact me private then i look up
for you
Op vr 1 aug 2025, 17:47 schreef AndriyNakonechnyy ***@***.***
…:
This module is locked in my car and i dont have live services and
internet. So I want to try use another module but dont want to remove
cockpit for this if this is possible.
—
Reply to this email directly, view it on GitHub
<#1040 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/BNOTOHSE7AN5UPGAP5DGMQ33LODX5AVCNFSM6AAAAAB2WOT2EOVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGOJWGA2DOOA>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
I have another one but i don`t now it status so i want to try connect it for checking status (i need tcu pinout for that reason). But if you can check my installed tcu it would be great. How can i contact you? |
Beta Was this translation helpful? Give feedback.
-
|
Hey thats not posible. The tcu unit is linked to the car.. you can not use
it on an other car. Due not only vin. But 3 other numbers that are
registered on the renault servers..4g netwerk sw nr. Hw nr.... only a new
one can to this.. you can contact me private on me email for more
information
Op vr 1 aug 2025, 18:35 schreef AndriyNakonechnyy ***@***.***
…:
I have another one but i don`t now it status so i want to try connect it
for checking status (i need tcu pinout for that reason). But if you can
check my installed tcu it would be great. How can i contact you?
—
Reply to this email directly, view it on GitHub
<#1040 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/BNOTOHUE6QMN5HTZB5JOG2T3LOJMNAVCNFSM6AAAAAB2WOT2EOVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGOJWGA4TEMY>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
I don't see your email 😔. It`s hidden. Maybe you can write me to andriy.nakon@gmail.com? |
Beta Was this translation helpful? Give feedback.
-
|
@Renotech1 hello, do you have any updates? |
Beta Was this translation helpful? Give feedback.
Uh oh!
There was an error while loading. Please reload this page.
-
Hy hope someone can help me. have a scenic iv from 2020 where i want to install reverse camera. anyone can help with a diagram to r-link 2 with 24 pin have tryed 18 cam+ 19 cam - 20 cam + suply but i dont work. thr camera an wire work when i connect to another schreen, so i think it is the wiring there is wrong...
Beta Was this translation helpful? Give feedback.
All reactions